Busch Light MN Walleye by MSK Designs

MSK Designs

Art>Signs & Logos

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 3 walls, 15% infill

Designer

5.5 h

2 plates

Boost

Released

Description

BUUSSSSSCCCCHHHHHHHHHH

Desgned a Busch Light Minnesota Light Box. Complete with a Walleye Jumping and some pine trees in the background as well.

This is designed to be printed in 4 colors with an AMS.

Then after it is printed, you can hang it on the wall. I've included a hanging hole on the back for a tack or nail.

Just need to add LED's to the inside and you are set.

Perfect for a gift for that fisherman in your life, or just someone that enjoys beer!

UPDATED 4/3/2024: Added a brim to the plug, just to make sure it doesn't break loose from the bed since it's so small (I've printed 15 of these and had one break loose, but don't want that to happen again). Then I also moved the backplate over on the buildplate a little bit to the right. I just had a recent print start to lift up since the top corner of it prints over the textured “Bambu Textured” words on the plate. Just a precaution to try to prevent this from happening to anyone else.

If you like Michelob Golden Light instead, you can find that version here:

https://makerworld.com/en/models/133009#profileId-144262

Below is a GIF of it printing. So far I've printed 3 and am working on other designs.

Check out my other light boxes:

Hamms Beer Bear: https://makerworld.com/en/models/153182#profileId-167364

American Flag/ Deer: https://makerworld.com/en/models/87724#profileId-93911

Michelob Golden Draft: https://makerworld.com/en/models/133009#profileId-144262

Minnesota North Stars: https://makerworld.com/en/models/230173#profileId-247482

Comment & Rating (11)

@lucky4meman

I’ve now printed 3 of these. I added a small slotted plug to put in the hole for the LED power wire to go through, so there is almost no gap where the wires go through. The power wire for my LEDS I used is 4mm and the slot in it is sized for that. Picture of the hole cover is attached and circled in red.

(Edited)

@dropshipper1234

Hey, really cool model. I printed one but was wondering if you'd share the step files so I can change the state outline? Looking to switch it to Wisconsin. Appreciate it either way

The designer has replied

@lucky4meman

I'll see if I still have them. They've been modified quite a bit with the fish jumping over the edge of the outline, but I still think you'd be able to modify it.

@dropshipper1234

Replying to @lucky4meman :

thanks I judt wanted to remove the state outline entirely and redesign from there

@lucky4meman

Replying to @dropshipper1234 :

I'll add the .step file to the project, but I don't know if they'll help or not. Took me a while to find the project again and the step file is showing a lot of errors now. But I'll still upload it and you can take a look. Will be uploaded in a couple minutes

@user_2516758048

This is the coolest sign I've ever seen. I don't have a 3d printer. Will you sell me one?

The designer has replied

@lucky4meman

Sorry, I just design them and print them for myself. I'm sure there is someone you know that has a 3d printer and could print it out for you. I just don't like to sell them or ship them.

@user_2516758048

Replying to @lucky4meman :

I dont know anyone but thank you anyways! If you change your mind just message me. I would pay good. Also I live in mn if you do too I could pickup.

@user_2001744290

How much does one of these cost, and how does one place an order? I'd love one for my fish house! Thanks!

The designer has replied

@lucky4meman

If you have a printer, it’s not much cost in material. Then just need to add in some strip led lights around the edge of them. We ended up putting one in our fish house as well. I don’t sell them online though.

No more