Laptop Stand - Foldable - Adjustable - PiP by Gallus Design

Gallus Design

Household>Office

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

Two Parts & Strong

Designer

3.2 h

1 plate

3.8(4)

Single Part & Light

Designer

1.5 h

1 plate

Single Part & Strong

Designer

1.6 h

1 plate

3.0(1)

Double Parts & Light

Designer

2.9 h

1 plate

1.0(1)

Boost

121

Released

Description

This is laptop stand that I designed for each size. It's print in plate so need assembly needed after print. Besides it stage of height so you can adjust the angle to what you want. Plus it's foldable, so only 11 mm thick (except hook) if you carry in your bag. Light model is less than 50gr each and strong enough to 13" laptops. If you have bigger laptop, then I suggest Strong version.

Comment & Rating (26)

@user_3447963747

Any idea with my stuff (T-T)

The designer has replied

@GallusDesign

try to print one by one (single part options) and silent mode (50% speed). I used bambulab filament with no issue.

@user_3447963747

Replying to @GallusDesign :

Thank you, I will give it a try.Do you think the problem is because I use the PEI pad, but my Heatbed settings are for the Bambu Cool Plate?

@user_3447963747

Replying to @user_3447963747 :

pei mat

@Jorge_chapero

I tried to print this on my P1S and this is what I got. Any idea?

The designer has replied

@GallusDesign

you have adhesion problem. you may use spray product (selling on bambu store) or add brim while you slice. I’d recommend start with adding brim. That would solve your problem quickly

@Jorge_chapero

Replying to @GallusDesign :

Thank you! It worked! I added brim 7 mm. Also cleaned the mat.

@GallusDesign

Replying to @Jorge_chapero :

glad to hear that :) nice print though

@dannijens

Print Profile

Two Parts & Strong

perfekt print. works perfectly to set my laptop at the same height as my main monitor. very stable and sturdy.

@user_3447963747

Hello, what's the nozzle size that you use for printing?

@ebkprints

did not work, hinged snapped right away

@user_3447963747

Hello, what's the nozzle size that you use for printing? My model is also snapped because the hinges are sticking together during printing, I guess.

@ebkprints

Replying to @user_3447963747 :

0.4

@user_3447963747

Replying to @ebkprints :

i use 0.4 too

@Shadowpheonix

Print Profile

Single Part & Strong

I tried several times to print this, and had issues with the hinge section fusing together every time. After some internet searching on fused 3d print in place models, I discovered the "X-Y Hole Compensation" setting in my slicer. Setting that to 0.15 resulted in a working print for me.

(Edited)

@user_802929422

Followed these instructions and it worked for me-- thank you!

@user_2487630028

Can i printet from my A1 mini?

@Nodesktophero

Looked nice & compact , but the top hinges immediately broke on first try (Bambu PLA) . If the hinge on both sides would be thicker, there would be a possibility to put a screw through...

@jp1001010101000

Print Profile

Two Parts & Strong

Parts warp a lot and cause adhesion problems even with part fans on, clean bed plate newly glued. I'm not sure if this is a problem due to the profile not heating the material enough or some other issue, but the long, quick sections at the end really pull up easily. Will try printing from my own slicer with my own speed settings to see if this helps or if I have a true adhesion problem