X1C-P1P-P1S Nozzle cleaning solution A1Strip
Copyright Claim
X1C-P1P-P1S Nozzle cleaning solution A1Strip
Boost
371
875
218
Print Profile(5)
PETG-0.2mm layer, 2 walls, 15% infill
Designer
29 min
1 plate
ABS-0.2mm layer, 2 walls, 15% infill
Designer
22 min
1 plate
ASA-0.2mm layer, 2 walls, 15% infill
Designer
21 min
1 plate
PC-0.2mm layer, 2 walls, 15% infill
Designer
21 min
1 plate
Click to see more
Boost
371
875
218
15
1 k
708
Released
Description
-Works on X1c, p1s, p1p
-Also added strenght on the poop stop wiping angle, was breaking too easily
-Added a nozzle wiper stand to glue a A1 Rubber tab, cut one 3x and enjoy the best nozzle wiper out there !!
-Superglue it up to make sure it does not fall off ! strongly suggest you glue it before placing it in place !!! super glue is a printer worst enemy !
Rubber cleaner : https://ca.store.bambulab.com/products/heatbed-nozzle-wiper-a1
Also fits perfectly to have the ultimate nozzle cleaner wiper !! : https://makerworld.com/en/models/100450#profileId-107193
Comment & Rating (218)
All
Print Profile
PETG-0.2mm layer, 2 walls, 15% infill
Noce little upgrade, need to get the A1 wiper!
The designer has replied
1
Reply
ty sir !!! i love it a lot too !!! appreciated !
0
Reply
Print Profile
ABS-0.2mm layer, 2 walls, 15% infill
100% Great 3D model
The designer has replied
0
Reply
amazing work !! thansk for the rating !!! appreciated
0
Reply
tysir !!! appreciated !!
0
Reply
Print Profile
ABS-0.2mm layer, 2 walls, 15% infill
Perfekto
The designer has replied
0
Reply
ty
0
Reply
Print Profile
PETG-0.2mm layer, 2 walls, 15% infill
Perfect🙏🏿🙃thanks
The designer has replied
0
Reply
ty
(Edited)1
Reply
Print Profile
PETG-0.2mm layer, 2 walls, 15% infill
Other Issues:I used it for a while, but the filament kept getting hung on the left side as you look at it installed. Then it would build up into a big blob. So, I had to take it out.
The designer has replied
0
Reply
thanks for the review, its something ive never ran into, and have it installed on all of my printers...sorry for the inconveniences, do you maybe have a wore out nozzle spewing out filament sideways ??
best regards
0
Reply
Replying to @TommyGunOG
No. Printer only has 433 hours on it. I may try it again, but I was worried to leave it on a multi colored print. I'll take a Pic of what it was doing if it does it again. Thanks.
0
Reply
Replying to @user_3756112297
433 hours is plently enough depending on what type of filament your using to have a wore off nozzle, specially if a stainless ....good luck
0
Reply
Print Profile
ABS-0.2mm layer, 2 walls, 15% infill
Print turned out great and 100 times better wiping especially with PETG.
The designer has replied
0
Reply
ty sir appreciate the review and rating :D enjoy !!
0
Reply
Print Profile
PETG-0.2mm layer, 2 walls, 15% infill
worked great, no complaints
The designer has replied
0
Reply
thanks for the review and rating
0
Reply
Print Profile
PETG-0.2mm layer, 2 walls, 15% infill
nickel fonctionne bien
The designer has replied
0
Reply
merci de la photo et du review/rating :D apprecier, bonne continuité a+
0
Reply
excelente work! thanks to share
The designer has replied
0
Reply
thanks for the pic and rating !!
0
Reply
Print Profile
PETG-0.2mm layer, 2 walls, 15% infill
perfect
The designer has replied
0
Reply
thanks for the rating and review !!! appreciated and !!! nice print !
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivativesRelated Models
© 2024 MakerWorld